NLGI grades explained: how to choose grease consistency

By Josh Malczak · Industrial & Fleet · Published 2026-11-08

Short answer: The NLGI grade measures how firm a grease is, from 000 (nearly fluid) to 6 (block-hard). NLGI 2 is the standard for most bearings and general use. Go softer (NLGI 1, 0 or 00) for centralized auto-lube systems, cold weather and enclosed gearboxes. Go firmer (NLGI 3) for some high-speed or vertical bearings. Consistency is only half the choice: base oil viscosity and thickener type matter just as much.

What the grade actually measures

The NLGI scale comes from a cone penetration test (ASTM D217). A standard cone drops into a worked grease sample at 77°F (25°C) for five seconds, and the depth it sinks, in tenths of a millimeter, sets the grade.

NLGI gradeWorked penetration (0.1 mm)Looks likeTypical use
000445–475Very fluidEnclosed gear cases, some auto-lube systems
00400–430Semi-fluidGearboxes, auto-lube in cold weather
0355–385Very softCentralized lube systems
1310–340SoftAuto-lube, cold-weather use, some heavy-load bearings
2265–295Peanut butterMost rolling bearings, chassis, general use
3220–250FirmSome high-speed or vertical-shaft bearings
4–685–205Very firm to blockSpecialty uses, rare in most plants

NLGI grade is not viscosity

This is the most common mix-up. A grease is base oil held in a thickener, a little like oil in a sponge. The NLGI grade describes the sponge's firmness. The base oil viscosity (for example ISO VG 100, 220 or 460) describes the oil that actually forms the lubricating film. Two NLGI 2 greases can behave very differently if one has a 100 cSt base oil and the other has 460.

Rule of thumb: higher speed calls for a lighter base oil, and slower speed with heavier loads calls for a heavier one. A slow, shock-loaded excavator pin wants a heavy base oil, often with moly. A fast electric motor bearing wants a lighter one.

When to go softer

When to go firmer

Don't forget the thickener

Lithium complex, calcium sulfonate and polyurea greases can all come in NLGI 2, but they handle water, heat and mixing differently. Some combinations aren't compatible, so purge the old grease when you switch. See how the thickener types compare.

Choosing grease: a quick checklist

  1. What does the OEM manual call for?
  2. Is it applied by hand or by an auto-lube system?
  3. What's the speed and load?
  4. What's the temperature range, especially the coldest start?
  5. Is there water, washdown or road salt?
  6. What's already in the bearing, and is it compatible?

Frequently asked questions

What does NLGI 2 mean?
It's a medium-firm grease, about the consistency of peanut butter, and the most common grade for bearings and general use.
Can I use NLGI 2 in an auto-lube system?
Sometimes, but many systems need NLGI 1 or softer, especially in cold weather. Check the system maker's spec.
Is a higher NLGI number better?
No. The higher the number, the firmer the grease, not the better. The right grade depends on the application.

Information here is general guidance. Always check your equipment manufacturer's recommendations and warranty terms.

Free download: PA Plant Lubrication Checklist

A one-page walk-through checklist for maintenance teams: storage, contamination, labeling, oil analysis and winter readiness.

Download the checklist (PDF)

Want a second set of eyes on your lubrication?

Tell me what you run and what's giving you trouble. I'll come out, walk the equipment, and give you a straight answer on what would help, whether or not you end up buying anything.

Request a lubrication review Call 724-406-9524