Coolant concentration control for CNC machine shops
Short answer: Check concentration with a refractometer at least once a week per machine, multiply the reading by your coolant's refractometer factor, and keep it inside the range on the product data sheet (often somewhere around 5% to 10% for general machining). Always top off with premixed coolant, not straight water or straight concentrate, and mix it by adding concentrate to water. Most coolant problems, like rust, rancid smell, foam, poor tool life and skin irritation, trace back to concentration drifting out of range.
Water-based metalworking fluid is one of the few lubricants that changes every single shift. Water evaporates off hot parts and chips, coolant leaves the machine on chips and parts, and someone tops off the sump with whatever is handy. A machine that started the month at the right mix can be far off by the end of it. The good news is that concentration is cheap and quick to check, and holding it steady fixes more coolant problems than any additive.
Why concentration matters
The concentrate carries everything that protects your tools, parts and machines: lubricity, rust inhibitors, the chemistry that keeps bacteria down, and the emulsifiers that hold it all together. Water carries the heat away. The ratio between them decides how the fluid behaves.
| Too lean (not enough concentrate) | Too rich (too much concentrate) |
|---|---|
| Rust on parts, fixtures and machine ways | Wasted concentrate, often the biggest hidden cost |
| Shorter tool life and poor surface finish | Foaming, especially with high-pressure through-tool coolant |
| Bacteria and fungus growth, rancid "Monday morning" smell | Skin irritation and dermatitis complaints from operators |
| Shorter sump life | Sticky residue on parts and machines |
The target range is on your coolant's product data sheet and depends on the job. Light machining of aluminum might run at the low end, and heavy cutting, tapping or grinding of tough alloys at the high end. Pick one target per machine or per job type and hold it.
How to check concentration with a refractometer
A handheld refractometer is the standard shop tool. Analog and digital models both work.
- Zero it with water at the start of the day, using the same water you mix coolant with.
- Take the sample from the sump while coolant is circulating, not from a stagnant corner or the top of a tank with tramp oil on it.
- Put a few drops on the prism, close the cover and read the line where light and dark meet (on an analog unit, hold it toward a light).
- Multiply by the refractometer factor. Every coolant reads differently. A coolant with a factor of 1.5 that reads 4 on the scale is actually at about 6%. The factor is on the data sheet, or your supplier can give it to you.
- Write it down: machine, date, reading, corrected concentration, and what you added.
If the line is fuzzy or hard to read, the coolant may be loaded with tramp oil or breaking down. That's a sign to look at the sump, not just add more concentrate. Our article on reading lab reports covers the same idea for oils: the trend matters more than one reading.
Top off the right way
- Use premixed makeup, not straight water or straight concentrate. Pouring water in lowers concentration, and pouring concentrate straight into a sump doesn't mix well and can leave pockets of very rich fluid.
- Mix makeup leaner than the sump target. Water evaporates but concentrate doesn't, so makeup at roughly half to two-thirds of your target usually holds the sump steady. Adjust based on your weekly readings.
- Add concentrate to water, never water to concentrate. Adding water to concentrate can form an unstable, greasy mix that won't emulsify properly.
- A proportional mixer (a venturi or water-powered unit at the faucet) takes the guesswork out of it and pays for itself quickly in most shops.
- Watch your water. Very hard water can cause scum and soap-like deposits, and very soft water can make some coolants foam. If you have recurring problems, test the water you mix with.
The other things to check while you're there
- Tramp oil: hydraulic oil, way oil and gear oil leaking into the sump. It feeds bacteria and makes refractometer readings unreliable. Skim it off and fix the leaks at the source.
- pH: many water-based coolants run in the 8.5 to 9.5 range (check your data sheet). A falling pH is often the first sign of bacteria, before the smell shows up.
- Chips and fines: clean chip trays and sumps regularly. Fines settle into sludge where bacteria grow.
- Machines that sit: coolant that doesn't circulate over a weekend goes rancid faster. Some shops run pumps briefly or aerate idle sumps.
Set up a simple routine
For most CNC shops, a weekly check per machine is enough, with daily checks on machines that run hard or have a history of problems. Keep a clipboard or spreadsheet at the coolant station with each machine's target and reading. After a month you'll see which machines drift and why. When it's time to recharge a sump, clean the machine with a system cleaner first so the new charge starts clean.
I supply Castrol Hysol and Quaker Houghton metalworking fluids, and I'm glad to walk a shop floor, check sumps and help set targets for each machine.